This guide makes container candles from a coconut wax blend. The temperatures and percentages are for our Creamy Coconut Wax (CCN1 by Calwax), which melts at 108 to 115°F (42 to 46°C). If you use a different wax, follow its data sheet where the numbers differ. Background on the material is in what is coconut wax.
Equipment
- Digital scale that reads in grams or tenths of an ounce
- Pouring pitcher and a double boiler (a pot of simmering water with the pitcher set inside)
- Thermometer
- Heat resistant jars or tins made for candles
- Wicks in two or three sizes, wick stickers and centering bars
- Essential oils, with the safety data sheet for each one
- Spatula or spoon for stirring
- Isopropyl alcohol and paper towels for cleaning jars
- Scissors or a wick trimmer
- Heat gun (useful for fixing tops)
- Warning labels
Step 1. Work out your wax and scent weights
Candle ingredients are measured by weight. Scent load is the weight of essential oil as a percentage of the weight of wax. To find the amount of oil, multiply the wax weight by the scent percentage.
CCN1 will hold up to 10 percent scent, which is the stated maximum for the wax. Here is the arithmetic for one pound of wax at 8 percent. The 8 percent is only an example to show the method, and the right load for your candle comes from testing.
- Wax: 16 oz (454 g)
- Essential oil: 16 oz x 0.08 = 1.28 oz (36 g)
- Total batch: 17.28 oz (490 g)
At the 10 percent maximum, the same pound of wax takes 1.6 oz (45 g) of essential oil.
More scent is not always better. Oil beyond what the wax can hold can seep out and leave the surface wet or oily, and in a soft coconut blend more liquid oil tends to make the finished candle softer. Essential oils differ from one to the next, so start low and test. See how to choose essential oils for candles.
Step 2. Prepare the jars
Wipe each jar with isopropyl alcohol and let it dry. Fix a wick to the center of the base with a wick sticker.
Step 3. Melt the wax
Weigh the wax into the pitcher and melt it in the double boiler. Stir occasionally and watch the thermometer. Heat until the wax is fully melted and clear, at or a little above the temperature you plan to pour at.
Stay with the wax the whole time it is on the heat.
Step 4. Add the scent
Weigh the essential oil in a separate container while the wax melts. Take the pitcher off the heat, pour the oil into the wax and stir gently until it is blended through.
There is no single established temperature for adding essential oils to wax. Check each oil's flash point on its safety data sheet before you start, and treat the temperature you settle on as a starting point to test.
Step 5. Pour
Pour temperature is where waxes differ most. The pouring temperature most often recommended for this wax is around 150°F (66°C). In our own use, CCN1 works best poured at 170 to 180°F (77 to 82°C) when the room is cooler, and 160 to 170°F (71 to 77°C) when the weather is hot.
Start in the range that matches your room, pour slowly, and tap the jar to release bubbles. Center the wick with a bar. Let the candles cool undisturbed at room temperature, spaced apart so they cool evenly.
CCN1 is usually a single pour. Because it is a natural wax, a batch sometimes needs a pass with a heat gun or a second pour to level the top.
Step 6. Trim and cure
Once the candle is solid, remove the centering bar and trim the wick to 1/4 inch (6 mm).
Curing is the rest period before a candle is burned. There is no single answer on how long, and no established figure for essential oils in coconut wax. Test your own candles at more than one cure time and keep whichever you choose consistent.
Wicking and why wick testing matters
The wick sets how hot and how wide the candle burns. No chart can pick it for you, because the right size depends on the jar diameter, the wax, the essential oils and their load, and any dye. Use a wick chart to choose the first size to test, then let your own burn tests decide.
A basic test follows this pattern.
- Make two or three identical candles, each with a different wick size from the same series. Label them.
- After curing, trim to 1/4 inch and burn them side by side. Burn for four hours at a time, with at least five hours of cooling between burns.
- At three to four hours the melt pool should reach to within 1/4 inch (6 mm) of the glass and be about 1/4 to 1/2 inch (6 to 13 mm) deep.
- Frequent soot or a wick that tips into the wax suggests the wick is too large. A ring of unmelted wax after the fourth burn suggests it is too small.
- Keep burning through the life of the candle. Judge the whole burn and not only the first few sessions.
Retest whenever you change the jar, essential oils, scent load or blend. Wick families and sizing are covered in how to choose a candle wick for natural wax.
Troubleshooting
| Problem | Likely cause | What to try |
|---|---|---|
| Sinkholes or rough tops | Air trapped in the wax escapes as it cools, and the surface collapses over the void | Poke the hole to release air, then use a heat gun on low or pour a thin layer of melted wax over the top. Adjust pour temperature by 5°F |
| Frosting | Tiny crystals growing on the wax surface. It is cosmetic and common in natural waxes, soy most of all | Stir gently, warm the jars, change pour temperature in 5°F steps, cool slowly at room temperature |
| Wet spots | Wax shrinking away from the glass as it cools | Clean the jars and warm them to about 100°F (38°C), pour slowly, space jars so they cool evenly |
| Soft or oily tops | More scent oil than the wax can hold | Lower the scent load, or firm the blend |
These causes and fixes are best documented for soy wax, and the same mechanisms are at work in a coconut blend. If softness is the recurring issue, see how to harden coconut wax.
Basic safety
Never leave melting wax unattended. Hot wax behaves like hot oil. Melt it in a double boiler so it cannot overheat, and keep a fire extinguisher nearby. Do not put water on a wax fire, because it can spatter burning wax.
Know what flash point means. A liquid's flash point is the lowest temperature at which it gives off enough vapor to form a mixture with air that can ignite. Essential oils vary widely, so check the flash point on each oil's safety data sheet, where it is listed with the physical and chemical properties. Keep essential oils away from open flames, heat wax by indirect heat, and stay within the scent load your wax is rated for.
Label every candle. The industry labeling standard, ASTM F2058, calls for three warnings, which the National Candle Association explains in its guide to candle labels. Keep a burning candle in sight, keep it away from anything that can catch fire, and keep it away from children. Many makers add burn directions such as trimming the wick to 1/4 inch before each use. If you sell candles, read the current standard itself before you print labels.
When your process is settled, you can compare other base waxes in candle wax types compared or browse our waxes.