Every candle wax is a trade-off between hardness, melt point, scent throw, appearance and price. This guide compares the five waxes makers ask about most, using figures from manufacturer and supplier data, and it covers the waxes we do not sell with the same care as the ones we do.
Comparison table
The ranges are typical published figures. Products vary by grade and supplier, so the data sheet for the wax you buy has the final word.
| Wax | Source | Typical melt point | Hardness | Scent load | Container or pillar | Notes |
|---|---|---|---|---|---|---|
| Coconut (blends) | Hydrogenated coconut oil, usually blended with other waxes | About 108 to 131°F (42 to 55°C), depending on the blend | Very soft | Up to 10% for our CCN1 | Container | Creamy tops and good glass adhesion. Softens and can sweat in heat. |
| Soy | Hydrogenated soybean oil | About 113 to 128°F (45 to 53°C) for container grades, 131 to 136°F (55 to 58°C) for pillar grades | Soft (container) to brittle (pillar) | Varies by grade. See the wax data sheet | Both, with different grades | Frosting and rough tops after burning are common. |
| Beeswax | Honeybee comb | About 144 to 149°F (62 to 65°C) | Hard but plastic | Often used unscented | Both | Has its own honey scent and color. High cost. |
| Rice bran | Wax removed from rice bran oil during refining | About 167 to 185°F (75 to 85°C) | Very hard, brittle | No standard published figure | Mostly used as a hardener in blends | Too high melting to use alone in most candles. |
| Palm | Fractions of palm oil | About 140 to 150°F (60 to 66°C) | Hard, crystalline | Varies by grade. See the wax data sheet | Both, with different grades | Feathered or crystal surface patterns. Sourcing is the main concern. |
Coconut wax
Coconut wax starts as coconut oil that has been hydrogenated to raise its melt point. It is almost always sold as a blend, because hydrogenated coconut oil alone is still very soft. Our coconut wax guide has the details.
Melt points depend on what the coconut is blended with. The Creamy Coconut Wax (CCN1 by Calwax) we stock is listed at 108 to 115°F (42 to 46°C). Other coconut blends run higher. Coconut apricot blends, for example, melt at about 121 to 131°F (49 to 55°C).
Pros. Smooth, creamy tops, good adhesion to glass, and very little frosting. Our CCN1 will hold up to 10 percent scent.
Cons. It is the softest wax on this list. It is a container wax only, and it can soften or sweat in warm rooms and summer shipping. See how to harden coconut wax.
Soy wax
Soy wax is hydrogenated soybean oil. Container grades melt low. The most widely used ones sit at about 113 to 119°F (45 to 48°C), and pillar soy waxes run around 131 to 136°F (55 to 58°C). As a rule, a wax needs a melt point of at least 135°F (57°C) to stand on its own as a pillar.
Pros. Widely available and well documented, with separate grades for containers and pillars.
Cons. Frosting (small white crystals on the surface) shows up in all soy waxes to some degree. It is cosmetic. Tops can turn bumpy after burning, and a strong scent throw can take more testing to get from soy than from other waxes. Pillar grades are brittle.
Beeswax
Beeswax is the oldest candle wax still in common use. Pharmacopoeias put its melt point at 62 to 65°C (about 144 to 149°F), according to the UN Food and Agriculture Organization.
Pros. Hard enough for pillars and tapers, and the FAO notes that beeswax candles stay straight at higher room temperatures. It also works as a hardener in soft container waxes.
Cons. It is expensive, it is an animal product (which rules it out for vegan lines), and its own scent and color compete with added scent. There is no standard scent load for beeswax, and its high melt point and hardness make it harder to handle than a container wax.
Rice bran wax
Rice bran wax is separated from rice bran oil during refining. It is one of the highest melting plant waxes. The FDA's food additive specification sets its melt point at 75 to 80°C, and our own lots are listed at 75 to 85°C (167 to 185°F).
Pros. A small amount firms up a soft wax or oil. In one study, 1 percent rice bran wax gelled olive oil, where carnauba needed 4 percent. It is plant derived, has very little odor, and can stand in for beeswax or carnauba in blends.
Cons. On its own it is brittle and melts too high for most candle designs, so it is a blending wax. Pound for pound it is pricier than the common candle waxes, and there is far less published candle testing for it than for soy. Read more in what is rice bran wax, or see the chunks and pastilles we carry.
Palm wax
Palm wax is made from the harder fractions of palm oil. Container grades melt at around 144°F (62°C) and pillar grades at around 150°F (66°C). Both are poured hot, at 200 to 210°F (93 to 99°C). Figures vary by grade and supplier.
Pros. Hard, good for pillars, and it forms crystal or feathered surface patterns that no other wax produces.
Cons. Sourcing. Palm oil is tied to deforestation in Southeast Asia, and certification has drawn criticism. A sustainable supply chain can be hard to confirm. If you use palm, ask your supplier for certification documents and judge them yourself.
How to choose
- Container candles with a creamy finish. Coconut blends or container soy. Expect to manage softness with coconut and frosting with soy.
- Pillars, tapers and votives. Beeswax, palm or pillar-grade soy. These need a melt point of roughly 135°F (57°C) or higher.
- Hot climates or summer markets. Pick a higher melt point wax, or harden a soft wax with beeswax, stearic acid or rice bran wax.
- Plant-based and vegan lines. Coconut, soy and rice bran wax. Check the full composition of any blend, since some coconut blends on the market contain a small share of petroleum wax.
Whatever you choose, test it in your own vessel with your own wick and essential oils. Scenting is covered in how to choose essential oils for candles. You can browse the waxes we stock in the wax collection.